navigasi

Jumat, September 23, 2016

bagaimana cara mereset switch cisco 2960

Memang manusia tempatnya salah dan lupa, atau memang kita tidak tahu, dikarenakan bukan kita yang konfigure switch csico 2960 tersebut dari awal, maka untuk dapat masuk kita harus melakukan Reset agar Cisco Switch Catalyst 2960 kembali ke Factory Default Setting
Berikut adalah langkah-langkah Mereset Cisco Switch Catalyst 2960 ke Factory Default Setting
Cara mereset Cisco Switch Catalyst 2960 ke Factory Default Setting disalin dari TKJ SMK Gondang
  1. Hubungkan kabel Console dari Switch ke PC melalui port Serial.
  2. dan nyalakan Switch, seketika lalu tekan dan tahan tombol "mode"

    Hal ini akan menyela proses booting sebelum menjalankan file sistem pada Flash, dan setelah beberapa saat (masih menahan tombol "mode") kita akan melihat tampilan seperti ini:

    Using driver version 1 for media type 1
    Base ethernet MAC Address: 4c:30:2d:81:ef:80
    Xmodem file system is available.
    The password-recovery mechanism is enabled.
    The system has been interrupted prior to initializing the
    flash filesystem. The following commands will initialize
    the flash filesystem, and finish loading the operating
    system software:
    flash_init
    boot
    switch:

  3. Bukalah Program Hyper-Terminal dan akseslah mode CLI.
  4. Jalankan file sistem Flash dengan perintah : flash_init

    switch: flash_init
    Initializing Flash...
    mifs[2]: 10 files, 1 directories
    mifs[2]: Total bytes : 1806336
    mifs[2]: Bytes used : 612352
    mifs[2]: Bytes available : 1193984
    mifs[2]: mifs fsck took 1 seconds.
    mifs[3]: 0 files, 1 directories
    mifs[3]: Total bytes : 3870720
    mifs[3]: Bytes used : 1024
    mifs[3]: Bytes available : 3869696
    mifs[3]: mifs fsck took 0 seconds.
    mifs[4]: 5 files, 1 directories
    mifs[4]: Total bytes : 258048
    mifs[4]: Bytes used : 9216
    mifs[4]: Bytes available : 248832
    mifs[4]: mifs fsck took 0 seconds.
    mifs[5]: 5 files, 1 directories
    mifs[5]: Total bytes : 258048
    mifs[5]: Bytes used : 9216
    mifs[5]: Bytes available : 248832
    mifs[5]: mifs fsck took 1 seconds.
    -- MORE --
    mifs[6]: 566 files, 19 directories
    mifs[6]: Total bytes : 57931776
    mifs[6]: Bytes used : 28429312
    mifs[6]: Bytes available : 29502464
    mifs[6]: mifs fsck took 21 seconds.
    ...done Initializing Flash.

  5. Hapuslah file config.text dari direktori flash:

    switch: del flash:config.text
    Are you sure you want to delete "flash:config.text" (y/n)?y
    File "flash:config.text" deleted

  6. Hapuslah file vlan.dat dari direktori flash

    switch: del flash:vlan.dat
    Are you sure you want to delete "vlan.dat" (y/n)?y
    File "flash:vlan.dat" deleted

  7. Reboot / restart switch dan selesai
    Cara mereset Cisco Switch Catalyst 2960 ke Factory Default Setting disalin dari TKJ SMK Gondang
    switch: boot
    Loading "flash:c2960s-universalk9-mz.122-58.SE2.bin"...
    --- System Configuration Dialog ---
    Enable secret warning
    ----------------------------------
    In order to access the device manager, an enable secret is required
    If you enter the initial configuration dialog, you will be prompted for the enable secret
    If you choose not to enter the intial configuration dialog, or if you exit setup without setting the enable secret,
    please set an enable secret using the following CLI in configuration mode-
    enable secret 0 

    ----------------------------------
    Would you like to enter the initial configuration dialog? [yes/no]:
    % Please answer 'yes' or 'no'.

    Cara mereset Cisco Switch Catalyst 2960 ke Factory Default Setting disalin dari TKJ SMK Gondang
  8. Sekian Cara Mereset Cisco Switch Catalyst 2960 ke Factory Default Setting

Tidak ada komentar: